This type of laser is the best thing you can add to your miter saw if you want some type of aid to show where the blade on the saw will cut. People argue that the shadow line devices are the best- I have both and think this laser is superior. This device puts a line on the material exactly where the blade will cut on the left side of the blade- where 99% of your cuts are made. The line is bright and super sharp- it diminishes in sunlight but you can see it. The shadow line is good, but for it to be accurate you have to bring the blade down to the material. If you don’t, the line is wider than the cut. Also, in sunlight you can’t use it. I like this tool so much more I added it to a saw with the shadow line. Buy it, put it on, use it! It’s as easy as that.

The blade performed as well as the Festool blade but at a better price. It's hard to find a saw sharpening company that will do a professional repair and sharpening job at a reasonable price. It's better to purchase a new blade and throw the old blade away.

Bought the 30 tooth for thicker ferrous metals and 50 tooth for thinner ferrous and both cut great for there specific intention. Bought 5 3/8" size and used on my M18 Milwaukee metal saw. No complaints other then wish they made it in a
5 1/2" or 5 7/8" so that I can fully cut through a bundle of light gauge 1 5/8" studs in one shot as the blade wears down. They do sell the 5 7/8" for thicker ferrous metal but not ideal for light gauge studs because leaves thicker burrs and not as clean cut.

Cuts great and great durability. Cut 3/16 plate smooth and easily. Compared to the original yellow brand I would say close to equal and good longevity. I use this saw alot so blades are important.

Saws right through steel tubing. I was cutting up an old 1 3/4" farm gate for scrap and the blade got stuck. I could not get it out of the cut as it was pinched in the cut and I could not restart my saw. It was stuck tight. I jerked the saw out of the cut and one of the teeth on the blade popped off. This is a very good blade and I just pass this experience on to other users. If the blade gets pinched and you can't wiggle it out, be careful.

I bought this only intending to cut sheet metal, which it does wonderfully well on my Dewalt track saw. I needed to cut a piece of 1/4" plate and was preparing to use my plasma cutter, but thought I'd give the track saw with Oshlun metal cutting blade a try. It worked! Had a go slow, but gave a nice clean cut, with a much better finish than what I'd get from the plasma cutter.

I'm an industrial electrician that uses M12 for my everyday tools. I bought an M12 Fuel Circular Saw 2530-20 specifically because I wanted to try to cut metal with it. The Milwaukee blade is half the price of the saw, so I wanted to try something less expensive.

This thing cuts like butter! Cable Tray, Strut, DIN rail, 3/8 mild steel plate, you name it. I'm VERY happy. I've done quite a few cuts and it doesn't seem to be slowing down, but I picked up a standby blade for when I finally bite off more than I can chew.

Wear a FACE SHIELD with this thing, she throws shrapnel like no other. I was only wearing safety glasses and a piece of metal bounced off my cheek, hit the glasses and then hit my eyeball. Had to go to the optometrist and everything, I had a burn and needed to take eyedrops for a week, luckily my vision came back.

I purchased this to replace my worn-out Irwin in my table saw. For the price, I'm happy with it. It is sharp, doesn't exhibit any vibration, and doesn't ring. I you've used older style solid steel blades, you know what I mean by "ring". One caveat is that if you're looking for a mirror finish cut on your material, or are looking for a blade to run glue joints, I don't think this will be what you're looking for. While the blade is extremely sharp, and tear-out is very very minor to not distant, the cut edge will have a touch of roughness from tooth marks. That said, I've used this with oak, maple, fir, pine, and cabinet-grade plywood with excellent results. When ripping fillers for cabinetry, the quality of the cut is more than acceptable for that type of work. You end up with a tight joint without tear-out or gaps. If the cut will be exposed, you will have to do a little sanding, but that is usually expected anyway. Only the highest quality blades, such a Forrest, will give you a cut that doesn't require very much in the way of hard work. For the price, I'm more than happy with this blade and will most likely purchase more in the future as I need them.

I bought the WEN track saw and was fairly impressed overall. The stock blade was horrible. I swapped it with this blade and man what a difference. I broke down a sheet of 3/4" birch and the cuts were very smooth with very little splintering. Very happy with this purchase.

Purchased to use in Wood! Why? The 1" bore.

To explain, we have a 12" "Original Saw Company" Radial arm saw in the shop. The 12" blades we have tend to be deafeningly loud, the outer rim speed is so high.
To combat this, we use 10" blades thus reducing the outer rim speed a good deal. This was easy to do with my old Delta R.A.S. that had the arbor more common in 10" blades ( 5/8" ) .
Since upgrading to the "Original" with the 1" Arbor (proper for 12" blades) I have had a very hard time finding any non custom made 10" blades with 1" arbor,.. until this one.
It makes very clean cross cuts in pine and hard woods. No tear out, super smooth.

And it is Soooooo quiet in the big R.A.S. we can no longer hear it over the dust collection.

I bought this blade set to make Dados and Rabbets for a couple of small projects I do around the house. Since my saw's arbor is a little shorter, but more importantly, part of the metal sawdust collection port is close to the blade, it can't handle typical Dado stacks. This blade set, due to it's unique design, gets in there and also fits within the stock choke plate! You have to wiggle the two blades as you install going one at a time, but since they mesh together on the arbor, it's rather easy.

NOTE: Both of these blades are easily twice as thick each as typical blades, so they're noticeably heavier. I was concerned the extra weight would cause issues with the motor or cutting in general, but nothing seems to be amiss. I do give the motor an extra couple of seconds to get up to speed before pushing through any material.

The two sizes this blade set cuts (1/4" and 3/8") are accurate and VERY clean. These are the perfect sizes to create box drawers from either 1/2" or 3/4" sheet goods, which is what I plan to in the near future, using either the "Quarter, Quarter, Quarter" method for 1/2" material, or "Half, Half, Half" for 3/4" material. Overall, I'm very pleased with this purchase.

I used this dado set just to check out the cut, I can't believe how fine of a cut this set makes. I cut a 1/4" tongue/groove to see the fit. No gaps, spaces and as smooth as glass. Then I cut just cut a whisper off to make a sliding tonque/groove, again, unbelievably smooth. This would make excellent drawer slides. I can't believe that a $150-$300 set could cut any better. A great bargain for $.

This blade is a great bang for the buck. It’s well made, has thick C-4 micrograin carbide, expansion slots with copper silencer plugs, and a stiff precision steel body. It’s very capable of glue ready edges right off the saw, and does a good job in many materials…it does everything a dependable general purpose blade should do. […] It clearly outperformed my $60 40T CMT 213.040.10. Hard to go wrong at the price.

I was extremely skeptical about using my Festool track saw to cut aluminum sheets. I was afraid aluminum would somehow wreck the saw and the track. I was wrong it works great. Perfectly straight cuts with very little burring. It did no damage to my saw or track, not even to the sacrificial nylon strip on the track. I used this blade to cut up two 4X10 sheets of .125" aluminum without a problem. I did not notice a decrease in performance at any point and the blade still appears to be razor sharp. Although I cannot compare it directly to Festool's version my opinion is that it would probably hold hold up just as well while at a fraction of the price.

I have never used a saw blade designed specifically for plastic before so I wasn't sure what to expect but this blade goes through plexiglass like butter. It cuts 1/8" and 1/4" thick sheets leaving a decent edge ready for 220-400 grit sanding. No nicks, cracks, chipping or melting. If you need to cut plastic this blade will do the job.

I was hesitant to buy this blade since there were no reviews to vouch for its quality.I am a professional trim carpenter and needed a blade that could last and cut cleanly.I decided to take a chance rather than spend three times more $ on the festool brand or one of the other alternatives out there.I have been extremely impressed with this blade and have found the blade indistinguishable from the festool in use and in long life between sharpenings.I am buying a couple more since I like to have several blades on hand at all times.

Only blades that fit my 5 3/8” fuel steel cutting circular saw from Milwaukee.

I Cut through about 160 1/2” steel rods and a bunch more extruded aluminum even though I shoulda used a non ferrous blade but so impressed I bought all of their brand blades for aluminum, steel and even wood since they’re the only ones that fit my saw; I have the Milwaukee Fuel Metal Cutting Circular Saw, I can only fit 5.5” blades with a 20mm arbor (most blades are 6”+ and only have a 10 mm arbor).

What no one adresses in any reveiws for a beam saw is the fact that many saws are underpowered for blades this size.

The Oshlun blade performs well as ripping or cross-cut blade. I performed many full depth rips w/ the blade in reclaimed cedar beams. All things considered it performed like a champ. I wish the saw had more power (older style Makita beam saw) I was concerned the blade may pinch o rjam and cause a nasty kick back, or worse yet get too hot and start to wobble / wander. None of the above happened. I'm a carpenter by trade, this is my first time w/ a beam saw, so take it for what its worth - Good price and fast shipping.

Good fit. Initial cuts worked well. I made 80+ cuts through that were 1-7/8" deep in 1" thick alum flatbar.
About 2/3s of the way through the blade started to struggle, but we were able to complete the project. Would probably recommend a cutting lubricant next time.

I've tried various brands of steel cutting blades over the years and feel like this is middle of the pack. It's way better than some out there in that the resulting edge is very clean with no burrs and isn't overly sharp. I made a pancake griddle out of 1/4" plate and didn't even have to sand the cut edge. It cuts 1/4" just fine but not quite as quickly as another brand I used before. But at half the price, I will buy these every time.

Quite impressed with the quality, durability, and value of this blade. I only used it to cut up to 2" x 2" square aluminum tubing and am pleased. It still seems to cut fine after dozens of cuts. That said I highly recommend this blade

So I "ran over " a steel bench dog with my Festool blade... Boo hoo my bad. There goes $80. Lesson learned, I'll buy a replacement. Here's an alternative... Hmm $24 for a similar tooth blade? Why not give it a try? Well glad I did! Great cut in 12mm birch plywood. Nary a scratch on the edge and splinter free--just like the $80 Festool blade! Now to stay away from those bench dogs... HIGHLY RECOMMENDED BLADE!

I have no idea why anyone would pay more than you would pay for this set. I had this exact set for years, it cuts very smooth bottom dados. I really like the full size chippers, and I’ve always been able to get the exact width that I need. I really don’t know why anyone would pay $100 more or $150 more just to cut smooth dados, I’m not thinking that the carbide tip blades in the $250 sets are going to last one minute longer than the carbide tips in this set. Due to circumstances beyond my control, I had to buy a new set, I did look around before purchasing this brand, and found no reason to buy anything different. Get it and you’ll be happy with it.

I needed to cut many aluminum cleats that were 34" down to 29.75" to fit on the back of the cabinets. I bought a DeWalt Atomic 4 1/2" saw during Xmas, and this blade was all I could find that would fit the saw. So I bolted this up and made my cuts with ease. Being too lazy to change blades, I use this blade to cut the wood rail buffers, and it cut the wood as good as the wood blade. After making about 20 cuts, the blade showed no signs of wear or loss of cutting power. The blade is very quick in speed and easy to control. Sure beat using a hack saw like I did last time. Kind of pricey, but time was not on my side. I searched all over the internet and Home Depot, but they only offered 7"+ blades.

I got this to cut damaged engineering wood flooring. The flooring is over concrete so I didn't want to chance the expensive Festool blade. So glad I made the purchase, the cuts were just about perfect. After I was done, I was able to use this to break down plywood sheets. Not as good as the Festool blade, but I can buy 3 of these for the same price.

With all those teeth is makes very smooth cuts. I'm working with red oak at the moment and this blade is doing exactly what I wanted it to do. The cross cuts are very good and I am very satisfied with the results. I've only had it for a couple weeks and so far it's not lost any teeth yet but I'll be keeping an eye on it.

I bought this blade not knowing what to expect, as I have never cut metal with this type of blade. I only needed to make about 50 cuts in extruded aluminum I-beam, so if it could complete that job, I would be happy. So far it has performed flawlessly. I even used it to cut some 1/2" EMT, though not recommended, it did the job. I may have shortened its useful life, but I cannot see how the quality of cut has been affected. I do recommend two things: First, use a wax cutting lube, and apply it every 5 or so cuts. Secondly, go nice and slow. For the price, I definitely recommend this blade.

I was a little concerned about the brightness after reading several reviews. Ordered anyway. I have LED lights on both sides of my miter saw and the laser showed up just fine. I'm not sure about durability but if I have a problem later I'll add a new review. Hardest part of installation was Loosening the Arbor nut.

Bought this blade to cut 1/8" thick rectangular tubing for a project I'm making. I got about 50+ cuts on it now and seems to wearing out just a tad now. I could not tell the difference between this blade and the Milwaukee metal blade and this blade is a lot cheaper.

We bought this for removing a breezeway between two buildings. We had to cut walls and the shingled roof, and then removed pieces with an excavator. This made the job pretty easy.
This blade is really heavy, and takes a bit ti spin it in the saw, but once it gets going, will cut through anything without issue. Cutting with it is pretty easy, if you can handle the hefty weight, otherwise it's easy to control.
Only downside was that it was definitely getting dull towards the end of the job. We had it sharpened, but haven't used it since, so we'll see if it's still usable or not.

Great price and good product, As a contractor these do not last long. Everyday usage cutting nails, copper, gyroc and wood. But the blades do the job needed.

I bought this blade to cut a hole in my work bench to install a tail vise. When I built the bench top years ago I foolishly used screws to join the slats together, so I knew it was a minefield. I didn't want to risk ruining my Festool blade, so I figured buying the less-expensive Oshlun blade was worth a shot. The Oshlun blade made a smooth, effortless cut in the wood bench top--almost as smooth as the Festool blade even though it's not advertised as a wood-cutting blade. I did hit a couple of the screws, and except for a few sparks, the blade went through them like they weren't there. I may never have to use this blade again, but this one use was worth the price I paid for it.

Using this on a Makita demo saw. Had a cheaper(McGills Warehouse) blade with 80 teeth on it. The McGills blade heated up and warped the blade plate while cutting so it wasn't much use. Fewer teeth on this blade and the way the carbide attaches(big shoulder on the plate behind the carbide) will make this blade much more durable and usable. Haven't seen any blade deflection yet but there's no wood sap build up on it yet. Cuts fast, doesn't jump or bounce much(use light pressure with the low tooth count as it cuts very aggressively).

This is an amazing saw blade for the price! I would suggest this blade to anyone with a cold cut saw. I bought one of these for a project to see how it would do on my Milwaukee Metal Cutting Circular Saw and it did better than the blade that came with the saw. I cut through 60ft. of 1/4 inch thick steel with no problem and the blade still had plenty of life in it. I only had to slow down because the saw itself got to hot to hold.
I bought 3 more of these blades after the first one, if you have a cold cut saw that uses an 8inch blade this is the blade to get. The price is great and the quality is fantastic.
This is defiantly a great buy not just for the money but for the quality.

I never post reviews. Haven't even had this blade 24 hours, but this thing is awesome. I used this on a Dewalt 20v circular saw, the regular one, not the metal cutting saw. I wasn't sure if my little battery powered saw would cut what I was wanting to cut, and I saw no reviews using this blade on a regular 20v circular saw. I cut a 4'x8' sheet of 1/4" steel lengthwise. I didn't try to go super fast, but I was putting pretty good pressure. I was cutting at about 1" per 15 seconds, so it took a while to go the full 8'. I cut 2 feet at a time with 5 minute breaks in between. used 2 full 5ah batteries, plus needed a third battery to do the last 3 inches. I tacked a piece of angle to my plate to ensure a straight cut. The cut quality is perfect, way better than what my plasma would have done, or even a shear for that matter. Took a little while, took some planning on how and what to use to hold it in place during the cut, but I couldn't tell any difference in cut speed near the end at all. Still looks sharp and ready to cut more plates of steel. As long as you use your head, this blade will do wonders. I would bet you could even cut 1/2" plate with no problems, just using lots of batteries. I highly recommend this blade.

If you're looking for the right blade to cut 8020 aluminium t slot, you can't go wrong with this blade. That's what I bought it for, and it has worked perfectly on my table saw. Just be sure to use some blade butter or some sort of wax or lubricant, and you'll get nice clean burr free cuts. I've used it on the 15 series 1515 and 1530 regular, lite, and ultra-lite profiles without issue.