Purchased to cut aluminum soffit for a residing project. It cut amazingly well and much faster and cleaner than using tin snips. I used a sled on my table saw and the cuts were clean without leaving dangerously sharp edges. I was surprised how clean it was on the thin material. It did bend the ventilation perforations slightly, but that was expected and not enough to cause any issues.

Excellent value, quality dado set. This has a good complement of chippers and shims to make nearly any width groove you want. The chippers cut smoothly with little to no vibration. The top-bevel teeth on the scoring blades (outer) do make a slightly deeper corner cut as described and as is the norm for this style dado. This dado set has much less tendency for chip-out compared to a router bit, and much improved resistance to burning compared to a router bit.

Oshlun Customer service is excellent. I received one shim with a slight manufacturing defect. Oshlun customer service provided a complete replacement shim set promptly upon identifying the problem to them.
Be aware that the shim set is manufactured to a tight tolerance fit to the arbor, as are the cutting blades. This can make removal of the shims and blades a little slow, but you are assured of good centering of the blades and shims on the arbor. I don't regard this as a defect.

I am very pleased with this dado set and recommend it. I also have an 8-inch Oshlun box joint saw set that has also pleased me.

Amazon Prime delivered very promptly and delivered pricing was excellent.

As a complete novice woodworker, I watched YouTube videos of people doing amazing and easy finger joints with dado stacks. Most said for basic work you don't need to buy a really expensive set.

Well, maybe you don't, but do not go the cheapest set your local store has. Get these instead.

I bought a Skil brand dado stack for 40 bucks at a local store. I made about 5 attempts at notches. I adjusted them, I tried every blade they gave me. All the cuts were horribly uneven, had a lot of blowout in the back, and I was extremely disappointed with them. I uploaded pictures of the best ones.

I then decided to go with suggestions on these reviews and give these a shot, for not much more than my terrible Skil experience. I got them today, tossed them on, and made a cut (I'm just using a miter gauge and a clamp for the test cuts).

I was amazed. It was a lazy cut, I'm not using a sled like I normally would, I'm not even using a zero clearance throat plate. Just a miter gauge. And the cut was near perfect and uniform. I uploaded several pictures.

There is no blowout the back, and in fact I can't even tell which side I cut from just by looking at it.

While I'm sure these aren't as precision as a much much more expensive set, for the relatively cheap price these are very worth it. Get them and don't waste your time with skil.

It's a good value. Of course it's made in China. Be sure to order a lube stick to use with it. If you are cutting thinner material like angle or box tubing, get the 120 Tooth. If you are cutting heavier bar stock, large rounds, get the 80 tooth. I ran the 120 tooth on some 3"x4" 7075 bar stock and it wanted to plug up even with plenty of lube.

Up to this point, I have only used friction and abrasive blades to cut steel. I was skeptical of a blade that looks just like your standard wood blade would work well and could last. But I have been very happy with the speed and smoothness of the cuts, and so far, the blade seems to have remained quite sharp. I've only cut about four 1/2" dia. bolts and a dozen or so 1/2" rebar, so it's still a little early to tell how long it will remain sharp. But it has saved me a lot of time and has kept the metal much cooler than with other blade types. I'm very happy with it so far.

Great blade for the price. I've been using this daily for over a year, and it still cuts clean and crisp. I make sure to remove any build-up of material behind the teeth, so it doesn't burn the wood, but other than that it's been no trouble at all. Definitely a decent alternative to the Festool blades.

Was looking for a replacement blade about a year ago when my original Makita beam was blade started getting dull. Found the Oshlun blade on Amazon and resisted buying it at first due to the low price. I just ordered my second one after using the first one 6 days a week for 10 months. We cut large Western Red Cedar, cypress, fir and spruce beams all day long with this blade (both rips and cross cuts). This blade has never warped under heating (and we really heat this thing up some days). Good blade at any price.

This dado set is very nice. The center blades have four cutting tips which makes for less tear out of the stock and less strain on my direct drive table saw. It makes very clean cuts on soft pine, and effortless clean cuts on hardwood too. Someone mentioned in one review to be careful when handling them and/or use gloves as the blades are very sharp and can easily cut you. That is a true statement. I highly recommend these if you’re a serious and/or experienced woodworker. The quality you get against the value is great.

Had mine about 3 years now. Use it all the time in my woodshop. Never had any problems with it. Works smooth, zeros in and keeps zero. I have noticed that occasionally the zero is off by a tiny, tiny bit, say half the width of the needle. I read in the company's description above that accuracy is +/- .001, so when I see it off zero, that tiny bit probably is .001. So mine is as accurate as described. The metal is nothing fancy, but it is smooth and machined well. Everything fits well and works. I am an avid woodworker. I use it for thickness planing, some joint work , measure the depth of a hole or groove, width of a groove, inside measurements, etc... The dial is easy to read and is in fractions, which I use. So no math involved. The fraction marks are in 64th's, you can also easily read between the marks to 128th's. If I cut a joint to 128th's of an inch you know it is a very good day in the shop indeed !!! Realistically if you are looking to buy one for very fine tolerances for fitting metal parts together or building machinery then you might want to go way up in price range. It's great for wood, the wood probably will move a 128th mark on a humid day anyway. I prefer a dial then a digital. I've read that a digital can round a measurement up if it falls between digits, that it uses energy when off, so batteries get used up. A dial lets you see the measurement when between digits or markings, so I know if just one more swipe of the plane will put it where I want it. I don't think you can buy more accuracy at this price range. For working wood I don't know why you would need expensive accuracy as the wood will move fine increments across it's grain overnight, just laying in your shop. Many woodworkers work down to a 32th of an inch in accuracy. So to be able to see a 128th is very close measuring for woodwork.

Love this blade. Bought for the low price and am quite suprised with the quality. I use it mostly for cutting wood and it does a great job. I also like that the blade is thicker and less prone to wobble therefore making better cuts. I will be looking at one for my miter saw (12") and see how that works out.

We have a need to cut through 1/4 inch thick x 8 inch fiberglass. Previously we've used a band saw which is very tedious and difficult to keep to a straight line. We bought this blade to put in our chop saw. It's worked perfectly. We can slice cleanly through the fiberglass sheet in just a few seconds. Obviously it throws out a whole lot more dust than a band saw so protective masks and good ventilation are important.

Was looking at cut off saws to work some of my 1/8th aluminum stock and while researching came across this 10" non-ferrous blade. The idea of swapping the blade on my miter saw and having the convenience and accuracy of the tool appealed to me so I made the purchase. Couldn't be happier. The saw easily cut through all the aluminum I threw at it and produced exceptionally accurate smooth cuts each time. My miter saw isn't the greatest (Kobalt 10") but with this blade working non-ferrous metals was easy. For anyone doing this for the first time, recommend eye protection. The blade creates very fine metal flakes while working.

I purchased this blade to cut some 1/8" thick aluminum angle stock with my 8.5" Hitachi sliding miter saw. The cuts were extremely clean, with essentially no burrs. After 20+ cuts (which obviously isn't much!) the blade is essentially new and cutting the same as when first installed.

This blade is a great bang for the buck. It’s well made, has thick C-4 micrograin carbide, expansion slots with copper silencer plugs, and a stiff precision steel body. It’s very capable of glue ready edges right off the saw, and does a good job in many materials…it does everything a dependable general purpose blade should do. […] It clearly outperformed my $60 40T CMT 213.040.10. Hard to go wrong at the price.

We bought this for removing a breezeway between two buildings. We had to cut walls and the shingled roof, and then removed pieces with an excavator. This made the job pretty easy.
This blade is really heavy, and takes a bit ti spin it in the saw, but once it gets going, will cut through anything without issue. Cutting with it is pretty easy, if you can handle the hefty weight, otherwise it's easy to control.
Only downside was that it was definitely getting dull towards the end of the job. We had it sharpened, but haven't used it since, so we'll see if it's still usable or not.

This is only a short term review as this blade has not seen a lot of use. It is installed in my DeWalt metal cutting saw. Cuts on aluminum tubing, flat bar, and angle are fairly clean and easy, leaving only small bits of scale on the tubing ends. I applied lubricating wax to the blade prior to using it and during the cutting process. There appears to be no aluminum residue build up after doing this.

I can not see any difference between my Festool blade and that one. Smooth cut with nice glossy feel to it.

There are a few things out there that are better options than Festool Replacement ones, all of which come at a better value.

Examples include t
1) Splinter Guard tape from Makita for the tracks which are way cheaper and better.
2) Bosh 35mm hose for 30$ ish compared with the 36mm from Festool at ridiculous price.
3) MFT3 MDF top that you can do yourself from any 3/4 MDF sheet.

Never using a stacked dado set before, I relied mostly on the reviews of the people here on Amazon (as I do for most of my purchases). Professional reviews from magazines or websites are nice, but I find that it's better to hear the feedback from actual Average Joe users. That said, it was a difficult decision choosing between the Oshlun and Freud sets, but after reading the reviews, I decided to spend a little less and go for the Oshlun set.

A big thing I keep reading in the reviews is how people feel the supplied box is just god awful and deduct a point or two for it. First off, I didn't spend $65 (6-inch set) for a cardboard box, I spent that much on the product inside. With that being said, and considering what people were saying about the box, I was really expecting something with a thickness less than a cereal box to be what held the dado set, but to my surprise, the box is actually very sturdy. It's also really nice that individual styrofoam cutouts were made to separate the saw blades so that they don't contact each other and chip the carbide tips. I plan on using the box as a long term storage piece for the time being until a time comes when I may need to build a wooden case for the set, but even then I'll use the original foam inserts for extra protection.

Aside from that, the blades cut a very smooth and flat bottom with very little chipout on the ends. The scoring was a little bit deeper than I had thought it would be initially, but it's not enough for me to worry about or deduct stars for. It hasn't done anything to lessen the quality of glue ups in my cuts, but if it had there's still 220 grit sandpaper to smooth it out in a few strokes.

Overall I am very pleased with this set. I've found it incredibly easy to change the setup and the included chart for sizes is really nice as well. I have no regrets about the purchase.

I bought these to use on my Mafell track saw when I was building my home and had a lot of richlite cladding and shelves to cut. That material is very hard on blades and after going through several Mafell blades I figured I could try these as they are much less expensive. They worked very well… durability was the same as Mafell. The kerf is a bit bigger which means I have to replace my rubber edge strip on my tracks when I go back to the Mafell blades. I haven’t tried these with wood so I can’t saw how clean they cut (Mafell blade leaves glass like finish). Anyway they are very good blades for the money.