So I "ran over " a steel bench dog with my Festool blade... Boo hoo my bad. There goes $80. Lesson learned, I'll buy a replacement. Here's an alternative... Hmm $24 for a similar tooth blade? Why not give it a try? Well glad I did! Great cut in 12mm birch plywood. Nary a scratch on the edge and splinter free--just like the $80 Festool blade! Now to stay away from those bench dogs... HIGHLY RECOMMENDED BLADE!

I've tried various brands of steel cutting blades over the years and feel like this is middle of the pack. It's way better than some out there in that the resulting edge is very clean with no burrs and isn't overly sharp. I made a pancake griddle out of 1/4" plate and didn't even have to sand the cut edge. It cuts 1/4" just fine but not quite as quickly as another brand I used before. But at half the price, I will buy these every time.

I have read several reviews for Dado stacks, and I thought I would give this one a try. A few reviews on other unnamed products are that the cut is uneven, the blades are all over the place and wobbly to grooved cuts and no repeatability. I am running this on a dewalt dw7345 contractors saw which is a 10" I opted for the 6" blade because I really don't see hte point in getting an 8" set for 20 bucks more when dado's are usually no more than 1" deep in extreme circumstances. the blades are dialed in on a micrometer and measure exactly what they claim, the shims are super accurate nad enable you to really dial in thicknesses to the micrometer. For the money this is a super sharp set up and has so many variations. I have shown one thing which I believe to be true on any saw blade single rip or dado. First cut was with no zero clearance image number three with all the tearout, and keep in mind this was baltic birch 1/2" plywood across the grain, with the grain with or without zero clearance was fine, and the second set is with a simple piece of hardboard over top, ran the blade up through it and successfully created a killer locking box joint using the 1/4,1/4, 1/4 method. I would recommend this to anyone!

I have an old 8" table saw, and NOBODY stocks, or even sells- that size, I shopped around to all the hardware and hardware box/super stores, (you know the twi I mean), and even Grainger could not get them!
When I went online, this was the only company that had 8" blades at a decent price, I found a couple others at 2 to 3 times the cost.
It cuts great, enough so that I got a 7.5" blade for my circular saw!

These Oshlun dado blades are the best that I've ever used. Having more chipper blades on the stacks make for a really nice smooth cut. I really recommend these blades.

We've used these as alternative to the more expensive brands. These blades are an excellent value. Last as long as the name-brand blades. We buy in bulk and use these daily in our work.

Product was shipped and delivered promptly after order was placed.

The blade set I received was in the aluminum case with heavy foam support around perimeter and foam sheets in between all blades. I am a weekend hobby woodworker and never used dado blades before the purchase. These work great for me! All the blades and shims in my set came clearly marked and I found it easy to make slight adjustments and dial in the exact width of cut I needed. I have a 15+ yr old JET JWTS series contractor saw and the blades and shims went on and off my factory 5/8" arbor with no problems. I will say that the shims can be a little tricky as they tend to find their way down into the arbor threads so be careful with that. All the blade teeth were complete and sharp (no nicks or quality issues as some other reviewers have cited). I have used once so far making many dado slots in MDF. The cuts were clean with a smooth, flat bottom. As the manufacturer clearly explains in the included literature the outer blade teeth are angled and slightly deeper intentionally to cut a crisp clean edge and bottom with minimal tearout. The minimal bottom corner groove produced by the outer blade teeth is barely noticeable and not a concern for me. Another positive for me was the full chipper blade design. I was down to this set or the similarly priced set from Freud. I had read a few reviews that indicated the partial chipper blades in the Fred set were not so easy to align and hold in place when installing on the arbor. That was a key factor in my choice of the Oshlun set. I have to say that even with the full chipper blades, aligning multiple blades for wider cuts can be tedious, especially if you need to use a few shims. I am very glad I went with the Oshlun in that regard because I understand now how much more difficult it would likely be with partial blades.

Overall I am 100% happy with my purchase and I highly recommend to anyone considering.

Other blade replacements I have found have a kerf to thin to clear the Dewalt tracksaw's riving knife. This Oshlun blade's kerf is wide enough to clear the knife and the resulting cut is excellent. It could use a bit more rake (tooth angle) to make the cut a bit easier, but overal this blade is a good replacement.

I own two other dado sets one being a Forest dado king and the other one is a Freud SD608 I am quite disappointed in the Forest set I have the Freud on a radial arm saw just to dado 2x4s for making shop carts. I had read some reviews on the Oshlun one stated that it was a bit tight to get on the arbor I own an older Delta cabinet saw and have no problems. The cuts in my opinion are amazing compared to my other sets and for the price you can't beat it. I especially love the full size chippers makes a world of difference. Thanks so much for a wonderful product.
Don

I bought this to cut up left over Ipe decking. That stuff is harder than the hub of hell. I am very sure on softwood even 20 years Doug fir it would cut like butter. The Ipe is too dense and the blade need more teeth to cut quickly.

Bosch CM10GD dual-bevel miter saw owner. If you purchase it on AMZ you can get the preinstalled laser guide for $80 more or without. I chose without, and after a year figured I'd spend the $20 on the separate module. This thing is great.

How to install: Seriously takes longer to write it up than do it. Unscrew two screws on the blade guard, unscrew (CLOCKWISE) main blade screw, put on laser, screw back in (COUNTERCLOCKWISE to tighten!) and replace blade guard screws.

MAYBE it took me all of 15 seconds. Maybe.

The laser line is exactly to the left of the kerf. The saw blade is exactly to the right of that line. If you're a half-blind half-fingered woodworker, position the line so it's just left of your offcut... and cut.

Why did I go a year without buying this... do yourself or your loved woodworker one a favor and get one of these. This was easier to install than any of the DIY projects i've done in ten years. I could gush for another hour.

I've bought these in the past and they perform well at a fraction of Fein's price. That said, they're not metal cutting like the Feins but they do a good job on wood.

I just received this today and I put it on my 12" miter saw to use the saw as a chop saw. I cut a piece of 1-1/2" x 1-1/2" 6061 aluminum. It cut that piece like it was hot butter. I used the Olsun blade lubricant before I did the cutting. No effort at all.
My next cut will be on a 2 1/2" x 2 1/2" of the same metal. If it cuts the same way, this blade is worth twice the price.

Best blade I have purchased in a long time. Tried a blade made by a different seller on Amazon. Said it was for alum but just loaded up. This blade goes through like butter....will buy again but don't think I can wear this out!

It cuts smoothly. With all blades there's still a speed of greatest precision. I apply an even pressure and let the blade do the work for the best results.
Aluminum smear deposits on the side of the teeth do not last long. I do not have a clogging problem with this blade as I have with others.
The steel is stiff and the kerf is consistent between different cross-sections and shapes of material. It doesn't wander.
I have cut very thin and small pieces with no biting or throwing of the piece. Other metal blades I've used bit into small, flexible, or poorly clamped pieces.
This is not an expensive blade and delivers excellent performance.

Never seen a saw with the primary purpose of cutting plastics, but as these become more and more common, I'm glad someone make a proper blade. Cuts well through Ultra-High Molecular Weight Poly(Ethylene) and Poly(Formaldehyde) / Poly(Oxymethanal). As those are two of the most physically impressive thermoplastics, I'm sure it'll cut through everything else just fine. As long as you push the plastic through at a reasonable speed, you'll get a clean edge with no melt deformation.

Works great so far. Who needs a $300 Milwaukee metal cutting saw when I can just put a $30 blade on a ghetto saw? I should take this to work just for the lolz.

I used to blade on my Makita SPK6000 Rail saw. It cuts just as good as the Makita blade. I was doing rip and cross cuts in Cherry veneered onto MDF, Cherry Ply and Birch Ply....all cuts were super clean. Only downside is the Makita is a 165mm blade stock...so you loose 2.5mm of cutting depth, not much of a down side when you see this blade is half the cost.

I couldn't be happier with this blade. It has allowed me to cut very small slivers of Avonite on my table saw. Before I had this blade if I tried to cut thin sliver the material would break ruining my piece. Silky smooth cutting…

I use this blade on a chop saw to cut wooden timbers imbedded with dirt, sand and occasional metal. I does a very good job. It won't stay sharp forever but I have had it resharpened and it works like new again. The person who sharpened it said I could probably have it sharpened 4 or 5 times more. It does the job I want it to. I don't recommend an inexperienced operator use it in this manner. You really have to know what you are doing to avoid pinching of the blade etc. I actually bought another one to use while the other is being sharpened.

I bought this blade because of the you tube “project farm” review (Best review channel). Understand only rated for ~1500rpm but installed on chop saw at 3300rpm and cut Aluminum, Raw Hide (Dog), PVC, and wood. Too much risk to cut anything harder but no tooth chips yet. Please take care, where leather wielding apron, face/neck shield, heavy jeans… a carbide tooth coming off at that speed can ‘hurt’ 🙂

I need to cut aluminum frequently but also hate changing blades on my miter saw because it takes 35 minutes to remove all the safety gizmos before spending 10 seconds changing the blade. Using the wrong blade on a 10" saw can be VERY dangerous, and some blades made for metal pretty much burn their way through wood. With this blade, I get great cuts on aluminum, as expected. I can also cut most other materials just as clean as with other blades, just slightly slower. I'd much rather cut a piece of wood in two seconds instead of one second rather than changing blades twice.

Metal blades can be very specific, even if they look basically the same. Don't use this for steel. I have one of their steel blades, and it's also good. Similarly, if you need to cut stainless steel, buy a blade for that. It might seem like a lot of trouble and money to have so many blades, but they exist for a reason. If you're not a pro, a good blade will likely last a lifetime, or at least until you buy that CO2 laser you've always wanted.

If you're looking for the right blade to cut 8020 aluminium t slot, you can't go wrong with this blade. That's what I bought it for, and it has worked perfectly on my table saw. Just be sure to use some blade butter or some sort of wax or lubricant, and you'll get nice clean burr free cuts. I've used it on the 15 series 1515 and 1530 regular, lite, and ultra-lite profiles without issue.

I had been delaying this purchase and finally ordered it. There were several chipped teeth on the first set. Absolutely no problems with return and replacement. Customer service the way it should be. Now, the dado set - A lot of teeth and real blades, not lightweight wings and they cut a FLAT dado with no tear out on the bottom or on the sides of the cut. The dado almost looks like it had been polished. Kinda makes me a little mad that I waited so long to make the purchase. I honestly cannot see how any other brand could make a better cut, regardless of the cost. Buy this one. You will not be sorry. For those that are concerned about the box - Exactly how much wood does a box cut? Besides, it gave me a new project.

I was a little concerned about the brightness after reading several reviews. Ordered anyway. I have LED lights on both sides of my miter saw and the laser showed up just fine. I'm not sure about durability but if I have a problem later I'll add a new review. Hardest part of installation was Loosening the Arbor nut.

Purchased to cut aluminum soffit for a residing project. It cut amazingly well and much faster and cleaner than using tin snips. I used a sled on my table saw and the cuts were clean without leaving dangerously sharp edges. I was surprised how clean it was on the thin material. It did bend the ventilation perforations slightly, but that was expected and not enough to cause any issues.

Oshlun makes the best saw blades I’ve ever used!!! I use this 60 tooth on my miter saw and get super clean cuts in all kinds of wood! I have an Oshlun 50 tooth blade in my table saw for general cutting work and it handles everything just fine!! Even hen I cut plywood I don’t get much chip out.

I mounted this on my recipricale saw and use it primarily for cutting 6061 aluminum extrusion. It works equally well on small 1X1" angle and also on larger 2X3" extrusion and cuts through it with ease. No lubricant/wax or other helper is needed on the cuts and the saw tracked just as cleanly as if it was cutting through wood What I like about this blade is the fact that it does not want to kick the part up or grab into the material so clampingon the part was only neceessary on one side. The surface finish of the cut was very similar to a semi finishing machining cut and required very minimal clean up of burrs, an added +. I have cut several hundred peices and there is no noticable depreciation or wear on the teeth and it works just as well as the first time I used it. Would recommend this for anyone needing to make quick work on aluminum cutting. Price wise this blade performed as well or better than my now retired Freud Diablo blade which cost me about $85 originally. Great value for the money and you won't find a comperable blade for less.

Just received this blade yesterday, and I put it to work cutting 45 deg angles to make Aluminum Window Screen frames. This blade is sturdy and strong, no wobbling on my cheap Delta Miter saw, and it cut through the aluminum frame like cutting through cheese. I did use a little bit of lub, i.e. WD-40, as the directions on the carton stated, but I do not think that I needed to do so. Prior to purchasing this blade, I had used the abrasive style blade to cut through the aluminum frame and the cut quality was a disaster, and not the quality that I will install on the front of my house. So I looked up the various blades that were available for cutting aluminum, and I found this one with great reviews. I went ahead and purchased it to try it out. Great value and great performance. Although there is another Oshlun blade available to cut aluminum with 60 teeth, but I opted to buy the 100 teeth blade which makes it much easier to cut through aluminum, and the blade will last a lot longer. I am glad I bought it.

One of the best blades I've owned over the last 30 years.

I bought this blade in May of 2014, bolted it up to a 10" Dewalt crosscut saw and started cutting 3 x 5 aluminum extrusion and several other types of aluminum. I've also cut PVC, ABS, and soft woods with it. The only thing I ever do to it is run a bit of beeswax over the teeth and sides once every month or two.

3-1/2 years later, and that same blade is still bolted up and cutting like the day I bought it.... minus all of the pretty red paint of course. 🙂

I admit...I haven't used this yet. I bought it based on reviews from several woodworking friends and decided on this set rather than cheaper dado versions. I've been a woodworker for decades and used the old wobble dado version by Craftsman and wanted something that was easier to fine tune the width. This has it! The blades are plenty substantial, very heavy, with a variety of thinner spacers to fine tune the dado width. I'm looking forward to using this and can tell it's going to be perfect for my dado needs.

I bought this blade with the intent of using it when I refinish my hardwood floors. I figured a $20 blade would be a lot easier to swallow if I hit something hard while cutting out some of the old damaged boards.

I did some test cuts on 3/4" birch plywood scraps. The cuts were clean and sharp. To be honest, I'm not sure that the festool blade could have done any better. Maybe the Festool blade would outperform this blade on other materials but for sheet goods I would consider them equal.

I'll be ordering a couple more blades. At this price I would be crazy if I didn't.

I bought this blade with the intent of using it when I refinish my hardwood floors. I figured a $20 blade would be a lot easier to swallow if I hit something hard while cutting out some of the old damaged boards.

I did some test cuts on 3/4" birch plywood scraps. The cuts were clean and sharp. To be honest, I'm not sure that the festool blade could have done any better. Maybe the Festool blade would outperform this blade on other materials but for sheet goods I would consider them equal.

I'll be ordering a couple more blades. At this price I would be crazy if I didn't.

I have two sets of calipers: this one and a digital electronic caliper by iGaging that reads in fractions, decimals, and metric. If I really need to dial in a measurement precisely, I use the iGaging. But 98% of the time the Oshlun is my go-to! It's the one I carry with me in my pocket, my tool bag, or even when I go to the store and need to measure a board or a bolt. It's so much easier to intuit the dimension of an object when I'm seeing a visual representation of where that dimension lies on the fractional "clock face." So many times when I use the other one - the digitial one - it will give me an answer of, say, 21/64ths and then I have to stop and spend two minutes doing math in my head and figuring out what that precise number means in practical terms. As a woodworker, I technically work to the nearest 32nd, but I THINK in terms of 16ths and 16ths "strong" or "weak". The Oshlun gives me that knowledge at a glance, without mental math and without hesitation. A machinist may need an instrument that can give them accuracy to the thousands of an inch, but for the work I do, the Oshlun Fractional Dial Caliper is the perfect tool for measuring when I need something more precise than my tape measure, alone. Highly recommended.

I love Festool, I buy their sanding pads for my rotex 150, I think you can't beat their quality products. I have to admit, forking out $125 for a replacement blade from Festool seemed steep. Went for this blade instead and let me tell you, this blade cuts just as good as the festool one, can't tell the difference, go for it. P.S: I cut wood only, not sure, if that's the case for other materials. Really glad I found this on Amazon.

I have found this dado blade to be excellent. The price was great, ease of use and setting up is far superior to the HF dado blade I returned after one of the shims jammed on the arbor of my Delta uni-saw and damaged the arbor threads on the 2nd use. That cost me $150.00 to for the purchase of a replacement arbor! Many customers complain that the storage box it comes with is not suitable. It is just a cardboard box. When mine arrived the box was broken on three sides. However the dado blades are very well packaged in foam and arrived with no damage. I simply made my own storage box from 1/2" plywood and utilized the foam packaging to safely store the dado blade.

Cuts great and great durability. Cut 3/16 plate smooth and easily. Compared to the original yellow brand I would say close to equal and good longevity. I use this saw alot so blades are important.

My dewalt track saw was wandering, after aligning the resharpened stock blade perfectly parallel, it was still binding in thick hardwoods. I’m glad I bought this blade instead of throwing my saw in the ocean, because it cuts better than ever. It’s a bit thicker than the stock blade which is a good thing, made a decent clean cut in 1-1/2” thick sycamore with zero burn marks.

Worked perfect for cutting a corian countertop to remove a dual bowl sink and install a stainless steel one. Worked well bht I could tell by the end of the cut it was tired. Great blade for the purpose and it worked well with the harbor freight Bauer brand 4.5 circular saw to do the job. For Corian it worked perfectly

I have been using these blades for several years as an economical alternative to Festool branded blades and I believe they may in fact be the same blade! Performance wise there is no difference at all. Would 100% recommend them to all serious woodworkers and DIY as well.

I can not see any difference between my Festool blade and that one. Smooth cut with nice glossy feel to it.

There are a few things out there that are better options than Festool Replacement ones, all of which come at a better value.

Examples include t
1) Splinter Guard tape from Makita for the tracks which are way cheaper and better.
2) Bosh 35mm hose for 30$ ish compared with the 36mm from Festool at ridiculous price.
3) MFT3 MDF top that you can do yourself from any 3/4 MDF sheet.

They have performed well when cutting very hard alloy roofing sheets, however, they do not last long on hard alloy. On soft metal I would expect them to last much longer.

My husband wanted an 80 tooth blade but as I kept searching for similar items the 120 tooth showed up and was significantly cheaper. I know cheap doesn't mean better but it has worked out great. What used to take 20 minutes of cutting with an 80 tooth blade took 5 minutes with a 120 tooth blade.

I was searching for a cheap blade for my Makita battery saw when I found this one that fits the Festool. Turns out to be perfect for the job. Not only does the blade cut just fine, but I hooked up the cyclone dust collection / vacuum and didn't have to breathe cement dust. Cutting the fiber cement didn't really do anything bad to the saw like I thought it might. Good blade but even better if you have the stuff to suck up the dust.

For the cash this is an unbeatable bargain. I cut what seems like a mile of aluminum U-channel with this blade in my DeWalt compound miter box and it sailed through it. ONE BIG POINT: You must use a lubricant when cutting aluminum or the aluminum will melt and fuse to the carbide tips of ANY blade, quickly destroying it, including this one.

The best, and most practical lubricant I've found is stick wax. You can use Stick-Kut from Relton, Castrol's Wax Stick or Boelube. These types of lubricants are packaged in what look like caulking gun tubes and are applied to the sides and teeth of the blade every twenty cuts or so. You can also use beeswax, paraffin or a candle. If you use these lubricants this blade should last forever.

Another big point is the work MUST be securely held. I made a fixture using De-Sta-Co clamps for my miter box which very securely held the aluminum channel I was cutting which made the entire process safe.

In short a super blade for a super price

This is only a short term review as this blade has not seen a lot of use. It is installed in my DeWalt metal cutting saw. Cuts on aluminum tubing, flat bar, and angle are fairly clean and easy, leaving only small bits of scale on the tubing ends. I applied lubricating wax to the blade prior to using it and during the cutting process. There appears to be no aluminum residue build up after doing this.

This is my new favorite demo blade.

I spent a day with this blade. It cuts rough, but for demolition work that doesn't matter. It managed to cut through a few hundred deck screws, and rip up a few sheets of plywood that had been coated in 1/4" thick epoxy and fiberglass. This blade is a beast - after all that it's still perfectly sharp and hasn't taken any damage. Besides being so durable, it's really QUICK cutting.

Prior to using this, I had been doing demo work with a sawzall with demo blades. This thing lasts way longer and cuts much quicker. After putting this in an old circular saw, I barely touched the sawzall.

I had a project that needed a blade that was not only one that would fit my compound miter saw but also one that would be designed for cutting aluminum. I went on line and googled my need and was pleased to find the Oshlun blade offered at a reasonable price. I read a few of the reviews that were on line relating to others that had purchased their blades and was convinced that I should do that too. I placed an order for the 8" 60 tooth blade designed for cutting aluminum and was pleasantly surprised how quickly I received it. I have used the new blade for cutting aluminum rails & other parts of the outside railing system that I am working on & the blade cuts all the aluminum parts perfectly. I am very happy that I made the purchase that I did. With out the new Oshlun blade I could not do the job that I have done.

I'm just a hobbyist woodworker, but I prefer quality tools - especially if they aren't too expensive. This dado set fits that description perfectly. Smooth, clean, flat bottom dados with no tear out. My first project with this set was in red oak, and I don't know how the set could have performed any better. Years ago, I bought an adjustable dado set - two blades mounted on a center hub that would let you tilt the blades in or out to change the width of you dado. Total junk. Literally could not make a flat bottom due to the design. Don't know if that type of dado set is still made, but if you see one, avoid it at all costs. I selected this Oshlun set because I thought the full blade multi-tooth chippers and the high tooth count on the outside blades would give a cleaner cut than the sets with fewer teeth and wing chippers with only two teeth. Don't know if that's true, but I am completely happy with the results I got with this Oshlun set. No regrets spending the money at all. The only negative is the advertised storage / carry case is simply a cardboard box with foam cutouts. Still a 5 star product.

I have had an old Makita Beam saw for years and years....this is the best blade I have used....Now it is also the first carbide tipped blade, but it sure works well. I am sawing PT fir lumber for retaining wall lagging; lots of it.....I am happy.

This is an amazing saw blade for the price! I would suggest this blade to anyone with a cold cut saw. I bought one of these for a project to see how it would do on my Milwaukee Metal Cutting Circular Saw and it did better than the blade that came with the saw. I cut through 60ft. of 1/4 inch thick steel with no problem and the blade still had plenty of life in it. I only had to slow down because the saw itself got to hot to hold.
I bought 3 more of these blades after the first one, if you have a cold cut saw that uses an 8inch blade this is the blade to get. The price is great and the quality is fantastic.
This is defiantly a great buy not just for the money but for the quality.

Excellent value, quality dado set. This has a good complement of chippers and shims to make nearly any width groove you want. The chippers cut smoothly with little to no vibration. The top-bevel teeth on the scoring blades (outer) do make a slightly deeper corner cut as described and as is the norm for this style dado. This dado set has much less tendency for chip-out compared to a router bit, and much improved resistance to burning compared to a router bit.

Oshlun Customer service is excellent. I received one shim with a slight manufacturing defect. Oshlun customer service provided a complete replacement shim set promptly upon identifying the problem to them.
Be aware that the shim set is manufactured to a tight tolerance fit to the arbor, as are the cutting blades. This can make removal of the shims and blades a little slow, but you are assured of good centering of the blades and shims on the arbor. I don't regard this as a defect.

I am very pleased with this dado set and recommend it. I also have an 8-inch Oshlun box joint saw set that has also pleased me.

Amazon Prime delivered very promptly and delivered pricing was excellent.

For the money this is a great saw blade. The 5 stars only applies to this price range since there are probably better blades for more money - but I'm not sure my saw would show any difference. I would definitely buy another one of these. My Grizzly track saw with this blade cuts as good (or even better) than my DeWalt table saw with a (Home Depot) Freud blade. BTW, I made a zero clearance device for my track saw so I get zero tear out on either side of the cut. I can't rate the blade for that since I never get any tear out with any blade.

If this saw blade cuts steel like my Oshlun aluminum cutting blade cuts aluminum, it will also be a winner. I haven't gotten to use it yet, but when I am through with a rush project I am currently working on, I will try it out on some steel shapes that I have in the garage. The unique tooth configuration should allow my 18 volt Firestorm Laser saw to cut steel effortlessly, and with carbide teeth it should last a long time. Stay tuned....

In addition to cutting sheet plastics, this blade cuts styrofoam sheets, leaving smooth edges and minimal "saw dust". I cut 1-inch and 2-inch thick sheets of styrofoam with excellent results. If you want to cut styrofoam with straight line rips, miters, etc. and have a table saw, this blade is the ticket.

I'm a big Festool fan. Well, I should say that I really like the Festool products that I currently own. I've owned a few green tools that....well.....sucked. The track saw is one of my favorites. Yeah, it's a little underpowered when cutting bevels but I rarely use it to make these cuts. One thing, IMO, that Festool doesn't do well is make blades. I've owned a couple of the Kapex saws and the blades provided are pretty sad. The fact that they provide a 60T blade with a $1400 miter saw is ridiculous. Do they really think someone is using this saw for something other than finish trim??? Sure it has a negative hook but still.... Back to the Oshlun blade. It cuts great. Super clean cross cuts and plenty fast when ripping 3/4 ply. I highly recommend this blade and will be purchasing another. I purchased the 80T for my Kapex and it's a great blade as well.

This review is for the Oshlun 10" 80 tooth fine finishing blade.

I've been purchasing Oshlun blades for the past year or two without complaint so far. This blade cuts nicely when your saw is properly tuned. Another reviewer indicates that they got blade markings, where that would ultimately be a function of a saw not correctly tuned. The runout on this blade isn't bad with a maximum runout of 0.006" and an average of 0.003" which provides glue ready cuts. Ideal blade runout is 0.005" or less.

The alternating top bevel grind on the teeth works excellent with natural woods and veneered plywood. The teeth are very sharp and the blade arrived with very little machine oil present, packed in a lightly padded cardboard retail package. You should consider seek a triple chip grind blade for heavy cutting of MDF and plastics.

The saw kerf is dead on 0.126" and has well-grounded copper plugged expansion slots, making the saw blade very quiet and smooth when running. Even though this blade has a positive hook angle, I wouldn't hesitate using it in a table saw, radial arm saw, or miter saw. Just please take the time to tune your saw before you rip into some wood and life will be good.

This blade is a great bang for the buck. It’s well made, has thick C-4 micrograin carbide, expansion slots with copper silencer plugs, and a stiff precision steel body. It’s very capable of glue ready edges right off the saw, and does a good job in many materials…it does everything a dependable general purpose blade should do. […] It clearly outperformed my $60 40T CMT 213.040.10. Hard to go wrong at the price.

Theses blades are incredible and when used properly work as good as any fine wood chop or miter saw. I bought one and one of my sub contractors, without permission, use it on a job site and bummed it up, so I bought another. No one get's to use it now that is not trained in it's usage.
Still going strong after several jobs and just as clean a cut as the first.

While i was worried that i would not be satisfied by these less expensive blades, i have been happily surprised. They are a great alternative to spending top dollar for Festool blades that are frankly a bit overpriced. I'd love to see the actual cost compared to mark-up on saw blades. Using a sharp blade saves time, improves quality and pleasure of work imensly. The option of Oshlun blades is a wonderful thing about capitalism, which usually is not so nice. While i might not use them on every job, 90% of the time they do a fine job and I see no difference (besides price) from the Festool blades. Recently I used a not new 48T Oshlun blade while ripping "Hardy Plank" I did a good 10 8 foot rips of the silica concrete board. I think the blade is toast, but even during the final rip it performed more than adaquately. I continue to be impressed and pleased with these blades. I'm lookin forward to see how they sharpen, just for kicks, I'ts probabaly cheaper to toss them, but my sharpening service does a great job, so it will be a worthwhile experiment.

Was looking at cut off saws to work some of my 1/8th aluminum stock and while researching came across this 10" non-ferrous blade. The idea of swapping the blade on my miter saw and having the convenience and accuracy of the tool appealed to me so I made the purchase. Couldn't be happier. The saw easily cut through all the aluminum I threw at it and produced exceptionally accurate smooth cuts each time. My miter saw isn't the greatest (Kobalt 10") but with this blade working non-ferrous metals was easy. For anyone doing this for the first time, recommend eye protection. The blade creates very fine metal flakes while working.

I bought these blades for my TS55. They were $15 each (now $48) and still WAY cheaper then festool blades. I have not noticed any difference in the quality of the cuts. I will buy more if the price comes down again... but for now I have a mini stockpile in the garage.

Was looking for a replacement blade about a year ago when my original Makita beam was blade started getting dull. Found the Oshlun blade on Amazon and resisted buying it at first due to the low price. I just ordered my second one after using the first one 6 days a week for 10 months. We cut large Western Red Cedar, cypress, fir and spruce beams all day long with this blade (both rips and cross cuts). This blade has never warped under heating (and we really heat this thing up some days). Good blade at any price.