What no one adresses in any reveiws for a beam saw is the fact that many saws are underpowered for blades this size.

The Oshlun blade performs well as ripping or cross-cut blade. I performed many full depth rips w/ the blade in reclaimed cedar beams. All things considered it performed like a champ. I wish the saw had more power (older style Makita beam saw) I was concerned the blade may pinch o rjam and cause a nasty kick back, or worse yet get too hot and start to wobble / wander. None of the above happened. I'm a carpenter by trade, this is my first time w/ a beam saw, so take it for what its worth - Good price and fast shipping.

This is my first DADO stack, I'm glad I didn't invest money on a larger one because this will easily hit any depth I'll need to make. It also goes wider than my 7941 supports (at 23/32" I can still use the arbor nut, I haven't tried going wider yet)

After some of the comments on other reviews, I was pleasantly surprised by the quality of the floor it leaves. Seemed extremely flat to me.

My only (minor) complaint is that I really wish the shims had slightly larger holes for the arbor. They are only a little hard to put on, but extremely hard to take off. I preferred to nudge my fence rather than try to go back and add another shim, but this time I wasn't doing a lot of repeated cuts. If I need to set up an exact width I anticipate a bit of annoyance.

I bought this blade with the intent of using it when I refinish my hardwood floors. I figured a $20 blade would be a lot easier to swallow if I hit something hard while cutting out some of the old damaged boards.

I did some test cuts on 3/4" birch plywood scraps. The cuts were clean and sharp. To be honest, I'm not sure that the festool blade could have done any better. Maybe the Festool blade would outperform this blade on other materials but for sheet goods I would consider them equal.

I'll be ordering a couple more blades. At this price I would be crazy if I didn't.

Works great so far. Who needs a $300 Milwaukee metal cutting saw when I can just put a $30 blade on a ghetto saw? I should take this to work just for the lolz.

This review is for the Oshlun 10" 80 tooth fine finishing blade.

I've been purchasing Oshlun blades for the past year or two without complaint so far. This blade cuts nicely when your saw is properly tuned. Another reviewer indicates that they got blade markings, where that would ultimately be a function of a saw not correctly tuned. The runout on this blade isn't bad with a maximum runout of 0.006" and an average of 0.003" which provides glue ready cuts. Ideal blade runout is 0.005" or less.

The alternating top bevel grind on the teeth works excellent with natural woods and veneered plywood. The teeth are very sharp and the blade arrived with very little machine oil present, packed in a lightly padded cardboard retail package. You should consider seek a triple chip grind blade for heavy cutting of MDF and plastics.

The saw kerf is dead on 0.126" and has well-grounded copper plugged expansion slots, making the saw blade very quiet and smooth when running. Even though this blade has a positive hook angle, I wouldn't hesitate using it in a table saw, radial arm saw, or miter saw. Just please take the time to tune your saw before you rip into some wood and life will be good.

I couldn't be happier with this blade. It has allowed me to cut very small slivers of Avonite on my table saw. Before I had this blade if I tried to cut thin sliver the material would break ruining my piece. Silky smooth cutting…

Up to this point, I have only used friction and abrasive blades to cut steel. I was skeptical of a blade that looks just like your standard wood blade would work well and could last. But I have been very happy with the speed and smoothness of the cuts, and so far, the blade seems to have remained quite sharp. I've only cut about four 1/2" dia. bolts and a dozen or so 1/2" rebar, so it's still a little early to tell how long it will remain sharp. But it has saved me a lot of time and has kept the metal much cooler than with other blade types. I'm very happy with it so far.

Was looking at cut off saws to work some of my 1/8th aluminum stock and while researching came across this 10" non-ferrous blade. The idea of swapping the blade on my miter saw and having the convenience and accuracy of the tool appealed to me so I made the purchase. Couldn't be happier. The saw easily cut through all the aluminum I threw at it and produced exceptionally accurate smooth cuts each time. My miter saw isn't the greatest (Kobalt 10") but with this blade working non-ferrous metals was easy. For anyone doing this for the first time, recommend eye protection. The blade creates very fine metal flakes while working.

Good fit. Initial cuts worked well. I made 80+ cuts through that were 1-7/8" deep in 1" thick alum flatbar.
About 2/3s of the way through the blade started to struggle, but we were able to complete the project. Would probably recommend a cutting lubricant next time.

Bought this to cut some 8020 stock to size on my saw and it went thru it like a warm knife thru butter. The cut that was left was a nice clean cut and I plan to use it for some more aluminum 8020 that I am using to build a Taig lathe stand for.
Pat

Did an excellent job cutting my kitchen countertop to size. After about 40 linear feet, it became noticeably duller. Overall, very plesed I was able to accomplish the job with just my small circular saw. I think it would do equally well for other brand names like Corian.

I've tried various brands of steel cutting blades over the years and feel like this is middle of the pack. It's way better than some out there in that the resulting edge is very clean with no burrs and isn't overly sharp. I made a pancake griddle out of 1/4" plate and didn't even have to sand the cut edge. It cuts 1/4" just fine but not quite as quickly as another brand I used before. But at half the price, I will buy these every time.

Using this on a Makita demo saw. Had a cheaper(McGills Warehouse) blade with 80 teeth on it. The McGills blade heated up and warped the blade plate while cutting so it wasn't much use. Fewer teeth on this blade and the way the carbide attaches(big shoulder on the plate behind the carbide) will make this blade much more durable and usable. Haven't seen any blade deflection yet but there's no wood sap build up on it yet. Cuts fast, doesn't jump or bounce much(use light pressure with the low tooth count as it cuts very aggressively).

Excellent tool. Mounted on a Chicago Electric, 6", cut off saw (9K rpm-no load). Cut through 1 1/4" x 1 1/2", 6061 aluminum bar stock with ease. With only mild pressure, the aluminum chafe flew. Gone in 30 seconds.

This is a great blade. I’m using it on a radial arm saw. Cuts are clean and accurate. The negative hook gives me much greater control when cross cutting with the radial arm saw because the blade isn’t so aggressive while traveling through the wood. When ripping “one by” pieces of pine or plywood I don’t have to push so hard and it allows me to feed the wood through at the optimum rate. It’s much safer than using a blade that’s intended for a table saw.

This blade works very well. I use it all the time in my line of work. I cut mostly 3/8 all thread rod with it on my milwaukee 28v cordless saw. very handy when you need to shorten all thread rod when your up 20 feet off the floor and need to make a quick cut.

I recently purchased the Oshlun LG-M01 Miter and Portable Saw Laser Guide for my miter saw, and I must say that it has been a game-changer for my woodworking projects. This laser guide has significantly improved the accuracy and precision of my cuts, making my work much more efficient and professional-looking.

The installation of the laser guide was straightforward and hassle-free. It fit perfectly on my miter saw and the alignment was easy to adjust to ensure that the laser line was accurate with my saw blade. Once installed, the laser guide provided a clear, bright line that helped me visualize exactly where my cuts would land, resulting in precise and clean cuts every time.

I particularly appreciate the portability of this laser guide. It is compact and lightweight, making it easy to transport and use on different job sites or workstations. The durability of the guide is also impressive, as it has held up well to regular use and has not required any adjustments or maintenance since I installed it.

Overall, the Oshlun LG-M01 Miter and Portable Saw Laser Guide has exceeded my expectations and has become an essential tool in my woodworking arsenal. I highly recommend this laser guide to anyone looking to enhance the accuracy and efficiency of their miter or portable saw cuts. It is a small investment that yields significant improvements in the quality of your work.

Great blade for the price. I've been using this daily for over a year, and it still cuts clean and crisp. I make sure to remove any build-up of material behind the teeth, so it doesn't burn the wood, but other than that it's been no trouble at all. Definitely a decent alternative to the Festool blades.

Quite impressed with the quality, durability, and value of this blade. I only used it to cut up to 2" x 2" square aluminum tubing and am pleased. It still seems to cut fine after dozens of cuts. That said I highly recommend this blade

Listen up guys. I was looking for a blade that would cut aluminum profiles and work on a Dewalt chop saw running at 2800RPM so I emailed the manufacturer and got an immediate positive reply about this blade. LOOK NO FURTHER. This blade cuts aluminium clean and fast. No Burrs.
Buy this with your eyes closed but make sure they are open when using it.

I upgraded my stock blade on my Bosch Surgeon Axle Glide compound mitre. For trim work, this is fantastic. The cut is smooth and minimal tear out, even on the underside, where most tear out occurs. The finish surface of the cut is so smooth that sanding is almost not needed. One other thing: almost no deflection in the blade. This stiff blade really helps with keeping the cut straight on wide boards.

Much nicer cut on plywood than the factory blade. Kerf size seems to be exactly the same so the lasers do not need adjustment between this and the Festool blade. I just got it so time will tell about longevity but as far as I can see at this point, paying more than double for the Festool 80t doesn’t seem to be a wise choice.

I bought these blades for my TS55. They were $15 each (now $48) and still WAY cheaper then festool blades. I have not noticed any difference in the quality of the cuts. I will buy more if the price comes down again... but for now I have a mini stockpile in the garage.