Quite impressed with the quality, durability, and value of this blade. I only used it to cut up to 2″ x 2″ square aluminum tubing and am pleased. It still seems to cut fine after dozens of cuts. That said I highly recommend this blade
My dewalt track saw was wandering, after aligning the resharpened stock blade perfectly parallel, it was still binding in thick hardwoods. I’m glad I bought this blade instead of throwing my saw in the ocean, because it cuts better than ever. It’s a bit thicker than the stock blade which is a good thing, made a decent clean cut in 1-1/2” thick sycamore with zero burn marks.
I love Festool, I buy their sanding pads for my rotex 150, I think you can’t beat their quality products. I have to admit, forking out $125 for a replacement blade from Festool seemed steep. Went for this blade instead and let me tell you, this blade cuts just as good as the festool one, can’t tell the difference, go for it. P.S: I cut wood only, not sure, if that’s the case for other materials. Really glad I found this on Amazon.
I bought this blade to use in my Harbor Freight 14″ chop saw. One feature of this blade was its rated rpm were higher than the Harbor Freight saw spins at. The 10″ blade limits the amount of material the saw can cut since it’s expecting to have a 14″ diameter blade, but for straight cuts it’s no problem. for 45° angle cuts it’s more limited.
I have made about 40 cuts through 1x1x1/8 and 1¼ x 1¼ x ⅛ box section, some cuts through 2 x 2 x 3/16 angle and 4 x ¼ flat steel, and the blade is still cutting pretty well – and a definite time saver over using a hand hacksaw!!
Love this blade. Bought for the low price and am quite suprised with the quality. I use it mostly for cutting wood and it does a great job. I also like that the blade is thicker and less prone to wobble therefore making better cuts. I will be looking at one for my miter saw (12″) and see how that works out.
Only blades that fit my 5 3/8” fuel steel cutting circular saw from Milwaukee.
I Cut through about 160 1/2” steel rods and a bunch more extruded aluminum even though I shoulda used a non ferrous blade but so impressed I bought all of their brand blades for aluminum, steel and even wood since they’re the only ones that fit my saw; I have the Milwaukee Fuel Metal Cutting Circular Saw, I can only fit 5.5” blades with a 20mm arbor (most blades are 6”+ and only have a 10 mm arbor).
This blade makes very very smooth cuts in hardwood, softwood, and plywood, using my Harbor Freight/Chicago Electric 10″ compound sliding miter saw. This saw is a bit underpowered compared to most, at only 11A. There’s just a very tiny bit of splintering on the bottom and back edges, but no chipping at all. The cuts are as smooth as if sanded, as smooth as S4S finished lumber. The blade definitely runs quieter than the blade which came with the saw. And, despite having 20 more teeth, it cuts through thick material better and faster than the stock blade did, especially 4x4s.
It was extremely difficult to find a reasonably priced blade with the negative hook appropriate to a sliding compound miter saw, and they are rare at any price. I really didn’t want to spend over $50, being as this is only a $100 saw! I would have preferred to spend only $25-30, but negative hooks could not be found in that range. I also went with this blade because of the full width kerf, which supposedly helps prevent blade deflection, especially on a SCMS. Some say a thin kerf makes better use of a lower powered saw, but the thick doesn’t seem to be a problem for my use. Most of the blades made for SCMS, ie negative hook, are thin kerf.
I highly recommend this blade! I cut a fair amount of plywood, so the extra money seemed justified, and as I said, I could not find a negative hook blade for any less. I just wish I could get it for as little money as the Oshlun positive hook 10″ blades! I’d happily settle for 60-tooth blade if it were $20 less.
This is my new favorite demo blade.
I spent a day with this blade. It cuts rough, but for demolition work that doesn’t matter. It managed to cut through a few hundred deck screws, and rip up a few sheets of plywood that had been coated in 1/4″ thick epoxy and fiberglass. This blade is a beast – after all that it’s still perfectly sharp and hasn’t taken any damage. Besides being so durable, it’s really QUICK cutting.
Prior to using this, I had been doing demo work with a sawzall with demo blades. This thing lasts way longer and cuts much quicker. After putting this in an old circular saw, I barely touched the sawzall.
Bought this to cut 2020 extruded aluminum on Festool Kapex, and works like a charm. Festool wants $175 for their blade, and hard to find blade with 30mm arbor that will fit festool saw.
Wow… just, wow! I needed a way to cut aluminum angle stock with my table saw for a project I was working on, and this blade was the best option that I could find. Given the relatively low price, I wasn’t sure what level of quality I could expect, but I really couldn’t justify buying a more expensive blade for a single project. Fortunately, I didn’t have to. When I tried it on a piece of scrap aluminum stock, the cut was excellent – smooth and clean, with very minimal burring. Even better, the blade cut through the light aluminum bar without any effort or binding. Nice! I cut the angle stock for my project and then found that with a blade that can cut soft metal so well, I had other projects that were suddenly practical. I’ve used the blade on aluminum, soft brass and hardwood so far, all with excellent results. This blade isn’t inexpensive, but it’s a bargain at the price if you need to cut softer metals and/or to make nice, smooth cuts on hardwood planks.
